naweritalia.blogg.se - Mifare card reader writer program

#MIFARE CARD READER WRITER PROGRAM SERIAL NUMBER#
#MIFARE CARD READER WRITER PROGRAM INSTALL#
#MIFARE CARD READER WRITER PROGRAM DRIVER#
#MIFARE CARD READER WRITER PROGRAM MANUAL#

As the result, the info or data for all 4 blocks (0, 1, 2 & 3) in sector selected will be shown in the Operation Window.įigure 13: Direct read operation of MiFare card Next, since the default authentication is done using Key A, make sure the KeyA checkbox is checked and enter the default authentication key FFFFFFFFFFFF in the Key textbox. Direct read from or direct write to the data blocks in memory of the MiFare can be executed under the Operation Window group box.ġ4. For the read operation, it is implemented in term of sector where the info or data for all 4 blocks in sector selected will be shown in the Operation Window as the read operation is executed.ġ5.

#MIFARE CARD READER WRITER PROGRAM SERIAL NUMBER#

As the result, the serial number or NUID (BA96B21F in this case) of the MiFare will be shown in the text box besides the Request button.ġ3. As the card request is successful, the MiFare is ready to be read or written. *The MiFare is need to be keep placing on the top of MiFare reader/writer throughout the operations introduced in the following sections.įigure 11: MiFare card at the top of the MiFare reader/writerġ2. Next, make the MiFare card request by pressing the Request button above the Purse Function group box. Firstly, please put the MiFare card close to or simply at the top of the MiFare reader/writer. This will open the communication panel for MiFare reader/writer with card type of MiFare_Std S50.įigure 10: Communication panel for MiFare reader/write with card type of MiFare_Std S50ġ1. Now, it is now ready to perform reading and writing operation to a MiFare Card.

Under the Antenna group box – turn on or off the antenna of the MiFare reader/writerġ0.After the communication port is configured accordingly, go to Choose Card (I) at the top of the window, choose the ISO1443A > MiFare_Std S50 option.

Under the Beep group box – adjust the time length for beep of the MiFare reader/writer.

Under the Icdeve group box – obtain the device number of the MiFare reader/writer.

Under the Light group box – turn on or off the LED on the MiFare reader/writer.

Model and version of the MiFare reader/writerįigure 9: Information regarding the MiFare reader/writerĩ.There are other operations which can be done in the port configuration panel like: The information regarding the model and version of the MiFare reader/writer, also with the types of card supported will be shown. *The locations highlighted in Figure 8 will show related notification message when a particular operation is executed in the MiFare reader/writer GUI.Ĩ. Next, under the Information group box, press the Get button. Press the Connect button afterwards.ħ. If the connection is successfully established, the success notification message will show at the top (in the Memo textbox) and the bottom (notification area) of the MiFare reader/writer GUI. The port configuration panel will appear as shown in Figure 6 below.Ħ.Under the Port Setting group box, select COM6 (in this case) as the communication port with baudrate, 19200bps (default communication baudrate of MiFare reader/writer). Go to Set(P) tab at the top of the window and choose the “Port Set” option. Establish the connections between the UC00A and the MiFare reader/writer using female to female jumpers according to picture shown in Figure 3 below.Ĥ.The starting page of the MiFare reader/writer GUI is similar as shown in Figure 5 below.ĥ. Firstly, the port for communication with MiFare reader/writer need to be configured. In this case, the COM port is COM 6.ģ.Next, solder the 1×7 header pin (male) to the flex cable breakout board of the MiFare reader/writer CR38 (RFID-ICRW-CR038) as shown in Figure 2 below.įigure 2: Solder header pins to flex cable breakout board of MiFare reader/writerĤ.

#MIFARE CARD READER WRITER PROGRAM DRIVER#

After the USB driver is successfully installed, with the UC00A still connected to the computer through USB miniB cable, the COM port assigned to UC00A can be checked through the Device Manager under the Ports (COM & LPT) category.

#MIFARE CARD READER WRITER PROGRAM INSTALL#

Download the driver of UART to USB Converter (UC00A) and install it according to the installation guides.

#MIFARE CARD READER WRITER PROGRAM MANUAL#

*Users are encouraged to go through the user manual of UC00A for better understanding on connections between MiFare reader/writer and UC00A. *Users are encouraged to go through the user manual of RFID-ICRW-CR038 for better understanding on how a MiFare reader/writer works. User manual and other related materials of UC00A can be downloaded from Cytron Technologies, UC00A.